GigaVUE® 420 Modules

GigaPORT

The GigaPort expansion module adds four copper and/or fiber optic Gigabit Ethernet ports to the GigaVUE-420 or GigaVUE-MP. Each port can be independently set as 10/100/1000 Base-T RJ-45 Ethernet, or 1000 Base-Sx/Lx/Zx Ethernet ports with multimode or singlemode SFP.

Optional Accessories:

• SFP (optical transceivers):
• SFP502: Sx 850 nm (550 Meter)
• SFP503: Lx 1310 nm (10km)
• SFP504: Zx 1550 nm (40km)

10GigaTAP

The 10GigaTAP module when installed in the back of the GigaVUE-420 provides the ability to split and copy inbound and outbound optical data streams. Replicant data is then forwarded to network monitoring tools at 1 or 10 Gbps. Gigamon's 10GigaTAP is available in three varieties to accommodate any fiber optic insallation.

10GigaTAP Options:

• SR-LC/Multimode, 850 nm
• LR-LC/Singlemode, 1310 nm
• ER-LC/Singlemode, 1550 nm

GigaTAP-Sx/Lx

The GigaTAP is a dual optical splitter module that adds 4 optical splitter ports to the GigaVUE-420 or GigaVUE-MP. GigaTAP-Sx and Lx modules provide the ability to Tap two fiber optic Gigabit Ethernet links (1000BASE-SX or 1000BASE-Lx). The GigaTAP-Sx/Lx modules use a passive fiber optic splitters to Tap the in-line signal flowing through the module for distribution to the GigaVUE-420 or GigaVUE-MP tool ports. There are two pairs of LC ports for Tapping two different MM or SM FDX fiber links. The split ratio is 70/30.

Note: GigaVUE-MP® is a first generation data access switch. It is no longer in production and has been replaced by the GigaVUE-420. The GigaVUE-MP is compatible with the GigaVUE-420 and remains supported for all systems under a support contract.

GigaTAP model numbers:

• TAP-202: MultiMode SR 850 nm
• TAP-203: SingleMode LR 1310 nm

GigaTAP-Tx

The GigaTAP-Tx module when installed in GigaVUE-420 or GigaVUE-MP provides the ability to Tap two copper Gigabit Ethernet links, copying traffic to specified tool ports as it flows through the Tap. There are two pairs of RJ45 connectors per module. Each pair TAPs a single 10/10/1000 Base-T FDX Ethernet link. The GigaTAP-Tx features fault tolerance and link failure propagation. Magnetic relays maintain the link even under power fail conditions. GigaTAP-Tx ports can be used as either network or tool ports.

Link TAP Mechanism:

• Electronically repeats the link signal when in ACTIVE mode and port-pairing is established.

GigaTAP model numbers (copper only):

• TAP-201: Dual copper 10/100/1000 ethernet TAP module

GigaLINK-Cu

GigaLINK modules provide high-speed connectivity to 10G links and can be used as network, tool, or stacking ports. GigaLINK modules can be installed in the x1, x2, x3, and x4 slots at the rear of the unit. Slots x1 and x2 can be used as stacking ports to extend your Data Access Network accross multiple chassis.

Optional Accessories:

• Stacking cable: CX4 copper cable (5/10/15 Meters)

GigaTAP model numbers (copper only):

GigaLINK-Fo

The GigaLINK -SR, -LR, or -ER adds one 10 Gigabit Ethernet fiber optic port to the GigaVUE-420. A single 10GigE XFP is included in each module.

GigaLINK model numbers:

• GLK-312: 10G port with MultiMode SR 850 nm (200 Meter) transceiver, LC connector
• GLK-313: 10G port with SingleMode LR 1310 nm (10 km) transceiver, LC connector
• GLK-314: 10G port with SingleMode ER 1550 nm (40 km) transceiver, LC connector

Optional 10GigE XFP transceivers:

• XFP-502 SR 850 nm (200 Meter)
• XFP-503 LR 1310 nm (10 km)
• XFP-504 ER 1550 nm (40 km)